Securing The Safe
How To Install
Articles
Included in this page...
Jump to a section click "number" or "go".
1 Overview of the Hide Away Safe Vehicle Fixing Kit.
2 How to install the Hide Away Safe Steel Vehicle Fixing Kit.
3 How to install the Hide Away Safe Marine Ply Vehicle Fixing Kit.
4 Installing the Marine Ply Vehicle Fixing Kit under a parcel shelf.
5 Suggestions for installation of the Marine Ply Vehicle Fixing Kit.
6 Installing flat to the floor in the boot or under one of the front seats.
7 Suggested fasteners to install the Vehicle Fixing Kit.
8 Australian manufacturer direct special offer between May 21, 2022 and May 31, 2022 save $$$ off RRP.
9 Other products and/or services you maybe interested in.
10 What to do next.
Some links on this page open in a new window.
There are two types of vehicle fixing kits for both the Hide Away Safe (mk2 smaller) and Hide Away Safe (mk3 larger).
This page explains how to install both and the suggested fastener types used to install both types of vehicle fixing kits:
very important before you do anything
When installing a Vehicle Fixing Kit you must first check what is underneath or behind the position of the installation before you drill the first hole to ensure your chosen fastener will not penetrate for example, the petrol tank or electrical wiring.
First...
Remove the Docking Station from it by undoing the high tensile nuts and washers securing it.
Second...
Install the Vehicle Fixing Kit to your Vehicle with Type 17 Wood Tek screws full thread 5/16” hex head drive or see number 7 near the end of this page for other suggested fasteners.
mk2 Steel Vehicle Fixing Kit
showing the installation fastenings and clinch studs.
Finally...
Once installed bolt the Docking Station back onto the Steel Vehicle Fixing Kit by placing the washers then screwing the high tensile nuts back onto the Steel Vehicle Fixing Kit clinch studs.
mk2 Vehicle Fixing Kit
with Docking Station bolted to it
installed to the floor in the rear of a Jackaroo 4WD.
mk3 Steel Vehicle Fixing Kit
with Docking Station bolted to it, installed in the rear of a Toyota Prodo Van.
If you have enough information
to make a decision to place your order
... we also give you ...
15 year
Australian manufacturer guarantee
Save $$$ today
Saturday May 21, 2022
off the RRP
When you receive the Marine Ply Vehicle Fixing Kit a Docking Station has already been affixed to it.
do not remove it
All that is required to install it to your vehicle is...
Hold the Marine Ply Vehicle Fixing Kit in the position it is going to be installed to, this is normally under the parcel shelf or to the floor in the boot and in some vehicles to the floor under the drivers or passengers seat.
With a pencil or similar mark the position where you are going to place all the fasteners in the Marine Ply Vehicle Fixing Kit.
mk2 Docking Station
fitted to a Marine Ply Vehicle Fixing Kit installed under a parcel shelf in a Commodore Sedan VT / VY.
mk2 Hide Away Safe
secured in a Docking Station under the parcel shelf in a Commodore Sedan VT / VY.
mk2 Docking Station...
Minimum of 2 fasteners front and rear but preferably 4 fasteners along the front and 4 at the rear.
mk3 Docking Station...
6 fasteners evenly spaced along the front and 6 at the rear.
Please note...
Some vehicle makes - models have punched out electrical wiring access holes in the Steel parcel shelf frame which may coincide with a chosen fastener location.
If this is the case simply bypass that location and place your fastener as close as possible to the punched out hole.
Pre-drill a pilot hole...
Through the Docking Station and the Marine Ply at the front and through the Marine Ply at the rear.
mk3 Docking Station
fitted to a Marine Ply Vehicle Fixing Kit installed under the parcel shelf in a BMW.
You may also use existing screw hole positions in the front of the Docking Station if any are more convenient to use.
To do this remove the existing screw and replace it with your chosen fastener.
Use your chosen fastener through the Marine Ply at the rear.
mk3 Hide Away Safe
secured in a Docking Station under the parcel shelf in a BMW.
Note...
Different vehicle makes and models may require different lengths of Marine Ply. If the Marine Ply we supplied is a little too long simply cut it to the required length.
If you have enough information
to make a decision to place your order
... we also give you ...
15 year
Australian manufacturer guarantee
Save $$$ today
Saturday May 21, 2022
off the RRP
Depending on how you intend to screw in the fastener (either by hand or with a drill with the appropriate screwdriver bit in it) depends on what you do next.
No matter whether you are screwing the fasteners in by hand or using a drill with a screwdriver bit we suggest you pre-drill both the Marine Ply and Steel.
Hold the Marine Ply Vehicle Fixing Kit in position and screw the first fastener through the parcel shelf, to the floor in the boot or to the floor under the front seat.
Once in position screw in the remaining fasteners.
The following refers to fitting in the boot and applies to both Marine Ply and Steel vehicle fixing kits.
you must
affix to a Steel floor pan or chassis
Note...
Affixing to cardboard or thin timber floor or to a polystyrene infill, as are in some vehicle makes and models after 2001, is not acceptable under any circumstance.
When affixing to a totally flat surface with full Steel support underneath or to the floor with carpet or rubber matting eg. under front seat, then the Marine Ply maybe able to be substituted in some vehicles with either.
mk2 Docking Station
secured under drivers seat in a Mercedes Benz MB Vito Van.
mk2 Hide Away Safe
secured in a Docking Station under the drivers seat in a
Mercedes Benz MB Vito Van.
If you have enough information
to make a decision to place your order
... we also give you ...
15 year
Australian manufacturer guarantee
Save $$$ today
Saturday May 21, 2022
off the RRP
The following is a suggestion about the fastener type used to install the both styles of vehicle fixing kits:
Type 17 Wood Tek screws full thread 5/16” hex head drive.
We suggest Wood Tek screws instead of Metal Tek screws because Wood Tek screws have a higher pitch between the threads than Metal Tek screws and has less chance of stripping when screwing them in.
Type 17 wood tek screws
full thread with hex head drive.
We highly recommend placing a fastener in every pre-drilled hole in the Steel Vehicle Fixing Kit and when installing the Marine Ply Vehicle Fixing Kit under the parcel shelf or to the floor - chassis follow number 4 above.
Various fixings to install the Docking Station.
Australian Manufacturer Direct Special Offer
...Theft Proof Security Products...
Today
May 21, 2022
until
May 31, 2022
save $$$ off RRP
for both the mk2 and mk3.
Plus...
free delivery anywhere in Australia
All other countries
we will quote the delivery cost.
Plus...
We post most orders two business days after receiving your full payment unless otherwise stated when placing your order.
Hide Away safe (mk2)
open Docking Station 4 insert boxes on side.
save
$178 off RRP
Hide Away Safe (mk3)
open showing the two removable insert boxes inside.
save
$188 off RRP
the world's highest security rated
virtually indestructible relocatable Safe
Read our offer Now...
If you have enough information
to make a decision to place your order
... we also give you ...
15 year
Australian manufacturer guarantee
Save $$$ today
Saturday May 21, 2022
off the RRP
Securing The Safe
How To Install
Articles
Copyright © 1994 – 2022
Speculator Holdings Pty Ltd
ABN: 78 433 438 794
... designed by ...
Internet Sales™
selling products & services
on the Internet since 1994
Last Updated
Saturday May 21, 2022
... member of ...
Theft Proof Security Products™
Australian made high security products